OpenModelica

8th MODPROD Workshop on Model-Based Product Development

Linköping University  –  www.modprod.liu.se  –  February 4-5, 2014

Organizers: Peter Fritzson, Petter Krus, Kristian Sandahl

Note: public versions of the presentations will be put on-line on the web

Download the pdf version of this document HERE

 

MODPROD Program Tuesday February 4, Tutorials and Workshop


08.30-09.00     Registration and coffee outside room A2, in Building A, Linköping University

09.00-10.45     Tutorials in Parallel, Length 3:15h

  • Tutorial 1: Peter Fritzson, Linköping University. “Introduction to Object Oriented Modeling and Simulation with Modelica using OpenModelica”. Hands-on Exercises, bring your laptop.
  • Tutorial 2: Wladimir Schamai, EADS, “Model-based Development using ModelicaML Value Bindings for Model Composition and Requirements Traceability”, hands-on exercises, bring your laptop.
  • Tutorial 3: Dirk Zimmer, German Aerospace Research Center, “Modeling and Simulation with the Planar Me-chanics Modelica Library”. Hands-on Exercises, bring your laptop.
  • Tutorial 4: Petter Krus, Linköping University, “System simulation with HOPSAN NG”. Hands-on Exercises, bring your laptop.
  • Tutorial 5: Martin Sjölund and Adeel Asghar, Linköping University;  Vitalij Ruge, Lennart Ochel, Willi Braun, and Bern-hard Bachmann, FH Bielefeld “Debugging Equation-Based Modelica Models; Dynamic Optimization with OpenModelica”. Hands-on Exercises, bring your laptop.


10.45-11.00     Coffee break outside room A2

11.00-12.30     Tutorials continued, same rooms as above

12.30-13.30     Lunch at Kårallen, Linköping University

13.30-15.00     Plenary Session 1, MODPROD Introduction, room: A2, Session Chair: Peter Fritzson

  • Amir Rashid, Royal Institute of Technology, Sweden, “Circular Business Models - Designing for Re-Manufacturing in Sustainable Manufacturing Systems
  • Peter Fritzson and Petter Krus, Linköping University, Sweden, “Presentation of Research at the Centre for Model based Product Development, MODPROD”


15.00-16.00    Coffee break + Poster Session and exhibition outside room A2, see poster presentation program

16.00-17.15    Session 2a, Sustainable Systems Engineering, room A2, Session Chair: Kristian Sandahl

  • Stefan Anderberg, Linköping University, Sweden, “Sustainability Challenges for Product Development”
  • Peter Fritzson, Linköping University, Sweden “World Simulation with Modelica and Implications for Sustainable Product Development”
  • Roland Samlaus and Philipp Thomas, Fraunhofer IWES, “Aero-servo-hydro-elastic Model Development for Wind Turbines with OneModelica”


15.50-17.15    Session 2b, Model-Based Engineering, room ACAS, Session Chair: Petter Krus

  • Nils Menager, Niklas Worschech, Lars Mikelsons, Bosch-Rexroth AG, Germany “A Tool Chain for Rapid Control Prototyping using Rexroth Controllers and Open Source Software”
  • Atiyah Elsheikh, Austrian Institute of Technology (AIT), Austria, “Derivative-based Hybrid Heuristics for Con-tinuous-time Simulation Optimization”
  • Lars Eriksson, Linköping University, Sweden “Model-based Development and Optimization of Engine Models”
  • Gert Johansson, Combitech AB, Sweden, “ArCon a Candidate for PolarSys Tool Suite”

 


17.40         Bus to Dinner Location

18.30         Workshop Dinner

MODPROD Program for Wednesday February 5

07.50-08.15      Bus passing main hotels, arriving Linköping University at 08.15

08.00-08.30      Registration outside room A2, Building A, Linköping university

08.30-08.40     Workshop 2nd Day, Introduction, Plenary Session (Chair: Peter Fritzson), room A2

08.40-09.40     Keynote, Johan de Kleer, Principal Scientist, Xerox Parc, California, USA, “Using Modelica for Early Stage De-sign, Reliability Analysis and Fault Diagnosis”

09.40-10.40    Keynote, Steve Mulski, Director Wind Energy Solutions, SIMPACK AG, Germany, “Model-based Development of Wind Turbines”

10.40-11.30    Coffee, Posters and Exhibition outside room A2, see separate poster presentation program

11.30-12.30     Parallel Session 3a, Model-Based Software and Systems Engineering. Chair: Kristian Sandahl, room A2

  • Simon Danielsson, KnowIT AB, Sweden “Model-based Development for Large-Scale Embedded Control Software Projects”
  • Håkan Kården, EuroStep, Sweden, “Multi-Disciplinary Collaborative Systems Engineering”


11.30-12.20     Parallel Session 3b, Model-Based Engineering. Chair: Petter Krus, room ACAS

  • Mattias Nyberg, Scania AB, Sweden, “Architecture Modelling of Automotive Embedded Systems and SW utilizing Architecture Recovery”
  • Claude Lacoursiere and Stefan Hedman, University of Umeå, Sweden “Strongly Coupled Distributed Simulations with FMI over TCP”


12.20-13.30     Lunch at Kårallen, Linköping University.  Posters and Exhibition outside room A2

13.30-14.40     Plenary Session 4, Model-Based Engineering and Applications. Session Chair: Petter Krus, room A2

  • Leon Starr, Model Integration, “xtUML, Simulink and Modelica:  How to use them together”
  • Akira Ohata, Toyota Motor Corporation, Japan, “A Desired Plant Modeling Environment for Automotive Control”


14.40-15.15    Coffee, Posters and Exhibition outside room A2

15.15-16.30    Parallel Session 5a, Model-Based Engineering. Session Chair: Petter Krus, room:A2

  • Nguyen Thuy, EDF – Electricité du France, France “Modelling & Simulation in Systems Lifecycle, from Early Conception to Operation and Modification”
  • Oliver Koch, Technical University of Dresden, Germany, “Aspects of System Integration in the Development of an Energy Efficient Power Management for a Wheel Loader”
  • Wladimir Schamai and Philipp Helle, Airbus Group Innovations, Germany, “Comparison of State Machines in UML2 and Modelica 3.3”


15.15-16.30    Parallel Session 5b, Model-Based Design and Development. Session Chair: Kristian Sandahl, room ACAS

  • Luigi Vanfretti, KTH – Royal Institute of Technology, Sweden, “Experiences on Power System Model Identification using Modelica and FMI Technologies”
  • Dag Fritzson, SKF, Sweden “Advances in Transient Multibody Simulation - SKF BEAST”
  • Martin Hochwallner and Stefan Fragner, Linz Center of Mechatronics GmbH, Austria, “Experience in Model Based Design with the Tool X2C in Controller Design in a Mechatronic Product Development Environment”


16.30-16.40     Break

16.40-17.10    Panel Discussion, (plenary session), room A2

You are here: